ASTM D5579-00
- Standard Test Method for Evaluating the Thermal Stability of Manual Transmission Lubricants in a Cyclic Durability Test
- standard by ASTM International, 01/01/2000
- Publisher: ASTM
$38.00$76.80
1.1 This test method covers the thermal stability of fluids for use in heavy duty manual transmissions when operated at high temperatures.
1.2 The lubricant performance is measured by the number of shifting cycles that can be performed without failure of synchronization when the transmission is operated while continuously cycling between high and low range.
1.3 Correlation of test results with truck transmission service has not been established. However, the procedure has been shown to appropriately separate two transmission lubricants, which have shown satisfactory and unsatisfactory field performance in the trucks of one manufacturer.
1.4 Changes in this test method may be necessary due to refinements in the procedure, obsolescence of parts, or reagents, and so forth. These changes will be incorporated by Information Letters issued by the ASTM Test Monitoring Center (TMC). The test method will be revised to show the content of all the letters, as issued.
1.5 The values stated in inch-pound units are to be regarded as standard. When materials, products, or equipment are available only in inch-pound units, SI units are omitted.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.7 This test method is arranged as follows:
Section | |
Scope | 1 |
Referenced Documents | 2 |
Terminology | 3 |
Summary of Test Method | 4 |
Significance and Use | 5 |
Apparatus | 6 |
Test Transmission | 6.2 |
Transmission Mounts | 6.3 |
Oil Circulating System | 6.4 |
Oil Return Hole | 6.5 |
Air Pressure Controls | 6.6 |
Drive System | 6.7 |
Instrumentation | 6.8 |
Thermocouple Placement | 6.9 |
Reagents and Materials | 7 |
Safety | 8 |
Preparation of Apparatus | 9 |
Cleaning of Parts | 9.1 |
Assembly | 9.2 |
Calibration | 10 |
Transmission and Test Stand Calibration | 10.1 |
Reference Oils | 10.2 |
Reference Oil Test Frequency | 10.3 |
Instrumentation Calibration | 10.4 |
Shift Time Calibration | 10.5 |
Operating Procedure | 11 |
System Flush and Charge | 11.1 |
Test Operation | 11.2 |
Shut Down Procedure | 11.3 |
Transmission Disassembly | 11.4 |
Determination of Test Results | 12 |
Failure Criteria | 12.1 |
Shifter Fork Wear | 12.2 |
Test Validity Determination | 12.3 |
Report | 13 |
Precision and Bias | 14 |
Keywords | 15 |
Test Validity Calculations and Limits | Annex A1 |
Test Kit Parts | Annex A2 |
Report Forms | AnnexA3 |
Data Dictionary | Annex A4 |
Manual Transmission Cyclic Durability Test Parts Inspection and Wear Measurements | Annex A5 |
Related Products
ASTM D4502-92(1998)e1
Standard Test Method for Heat and Moisture Resistance of Wood-Adhesive Joints..
$30.00 $60.00
ASTM D2829-07
Standard Practice for Sampling and Analysis of Existing Built-Up Roof Systems..
$26.00 $52.80
ASTM D4454-85(2009)
Standard Test Method for Simultaneous Enumeration of Total and Respiring Bacteria in Aquatic Systems..
$23.00 $46.80
ASTM F1901-10
Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems..
$26.00 $52.80